BAS standards at public enquiry

Institute for Standardization of Bosnia and Herzegovina, on the proposal of BAS technical committees, announces a public enquiry on draft national standards (stage code 40.20).

Deadline for submission of comments on draft national standards is 60 days from the publication of the enquiry on the Institute's website (if necessary, it can be shortened to no less than 30 days).

The drafts of BAS standards are available to our stakeholders via online module for reading the draft of BAS standards, and basic information about the draft (title, scope, technical committee that prepared the draft for public discussion, etc.) is available on the ISBIH website. 

The request for access to the draft BAS standard at the public enquiry should be sent to email: stand@isbih.gov.ba. To be able to access the online module for reading the draft BAS standards, you must be registered on our website.

Written comments on the draft national standards (with the designation of BAS technical committee and the reference designation of the BAS draft standards) shall be submitted to the Institute. 

To fill this form correctly, see the Comment Form Use Guide.

Showing 661-680 of 1,067 items.
Standard referenceStage codeBAS/TCReal dateForseen date for next stage code
   
nsBAS EN IEC 63376:2025
Industrial facility energy management system (FEMS) - Functions and information flows
40.20BAS/TC 5124.04.202523.06.2025
nsBAS EN IEC 63403-1:2025
Horticultural lighting - LED packages for horticultural lighting - Part 1: Specification sheet
40.20BAS/TC 1911.06.202505.08.2025
nsBAS EN IEC 63403-2:2025
Horticultural lighting - LED packages for horticultural lighting - Part 2: Binning
40.20BAS/TC 1911.06.202505.08.2025
nsBAS EN IEC 63404:2025
Switchgear and controlgear and their assemblies for low voltage - Integration of radiocommunication device above 380 MHz into an equipment
40.20BAS/TC 5223.04.202523.06.2025
nsBAS EN IEC 63461:2025
Pelton hydraulic turbines - Model acceptance tests
40.20BAS/TC 5616.05.202516.07.2025
nsBAS EN IEC 63522-8:2025
Electrical relays - Tests and measurements - Part 8: Timing
40.20BAS/TC 1813.05.202506.07.2025
nsBAS EN ISO 10253:2025
Water quality - Marine algal growth inhibition test with Skeletonema sp. and Phaeodactylum tricornutum
40.20BAS/TC 715.05.202515.07.2025
nsBAS EN ISO 10297:2025
Gas cylinders - Cylinder valves - Specification and type testing
40.20BAS/TC 4123.05.202522.07.2025
nsBAS EN ISO 10364:2025
Structural adhesives - Determination of the pot life (working life) of multi-component adhesives
40.20BAS/TC 924.04.202523.06.2025
nsBAS EN ISO 105-B04:2025
Textiles - Tests for colour fastness - Part B04: Colour fastness to artificial weathering: Xenon arc fading lamp test
40.20BAS/TC 4813.05.202514.07.2025
nsBAS EN ISO 105-C12:2025
Textiles - Tests for colour fastness - Part C12: Colour fastness to industrial laundering
40.20BAS/TC 4813.05.202514.07.2025
nsBAS EN ISO 10705-3:2025
Water quality - Detection and enumeration of bacteriophages - Part 3: Validation of methods for concentration of bacteriophages from water
40.20BAS/TC 715.05.202515.07.2025
nsBAS EN ISO 10714:2025
Steel and iron - Determination of phosphorus content - Phosphovanadomolybdate spectrophotometric method
40.20BAS/TC 430.05.202530.06.2025
nsBAS EN ISO 10882-1:2025
Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator's breathing zone - Part 1: Sampling of airborne particles
40.20BAS/TC 224.04.202523.06.2025
nsBAS EN ISO 10882-2:2025
Health and safety in welding and allied processes - Sampling of airborne particles and gases in the operator's breathing zone - Part 2: Sampling of gases
40.20BAS/TC 224.04.202523.06.2025
nsBAS EN ISO 11243:2025
Cycles - Luggage carriers for bicycles - Requirements and test methods
40.20BAS/TC 3511.06.202510.08.2025
nsBAS EN ISO 12224-1:2025
Solder wire, solid and flux-cored - Specification and test methods - Part 1: Classification and performance requirements
40.20BAS/TC 224.04.202523.06.2025
nsBAS EN ISO 12224-2:2025
Solder wire, solid and flux-cored - Specification and test methods - Part 2: Determination of flux content
40.20BAS/TC 224.04.202523.06.2025
nsBAS EN ISO 12643-1:2025
Graphic technology - Safety requirements for graphic technology equipment and systems - Part 1: General requirements
40.20BAS/TC 4023.04.202522.06.2025
nsBAS EN ISO 12643-2:2025
Graphic technology - Safety requirements for graphic technology equipment and systems - Part 2: Prepress and press equipment and systems
40.20BAS/TC 4023.04.202522.06.2025