BAS standards at public enquiry
Institute for Standardization of Bosnia and Herzegovina, on the proposal of BAS technical committees, announces a public enquiry on draft national standards (stage code 40.20).
Deadline for submission of comments on draft national standards is 60 days from the publication of the enquiry on the Institute's website (if necessary, it can be shortened to no less than 30 days).
The drafts of BAS standards are available to our stakeholders via online module for reading the draft of BAS standards, and basic information about the draft (title, scope, technical committee that prepared the draft for public discussion, etc.) is available on the ISBIH website.
The request for access to the draft BAS standard at the public enquiry should be sent to email: stand@isbih.gov.ba. To be able to access the online module for reading the draft BAS standards, you must be registered on our website.
Written comments on the draft national standards (with the designation of BAS technical committee and the reference designation of the BAS draft standards) shall be submitted to the Institute.
To fill this form correctly, see the Comment Form Use Guide.
| Standard reference | Stage code | BAS/TC | Real date | Forseen date for next stage code |
|---|---|---|---|---|
| nsBAS ISO 4250-1:2025 Earth-mover tyres and rims — Part 1: Tyre designation and dimensions | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 4250-2:2025 Earth-mover tyres and rims — Part 2: Loads and inflation pressures | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 4548-13:2025 Methods of test for full-flow lubricating oil filters for internal combustion engines — Part 13: Static burst pressure test for composite filter housings | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 4548-14:2025 Methods of test for full-flow lubricating oil filters for internal combustion engines — Part 14: Hydraulic pulse durability for composite filter housings | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 5775-1:2025 Bicycle tyres and rims — Part 1: Tyre designations and dimensions | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 6519:2025 Diesel engines — Fuel injection pumps — Tapers for shaft ends and hubs | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 6798-3:2025 Reciprocating internal combustion engines — Measurement of sound power level using sound pressure — Part 3: Survey method for use in situ | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 7151:2025 Surgical instruments — Non-cutting, articulated instruments — General requirements and test methods | 40.20 | BAS/TC 25 | 13.10.2025 | 12.12.2025 |
| nsBAS ISO 7870-6:2025 Control charts — Part 6: EWMA control charts for the process mean | 40.20 | BAS/TC 38 | 31.10.2025 | 30.11.2025 |
| nsBAS ISO 8092-2:2025 Road vehicles — Connections for on-board electrical wiring harnesses — Part 2: Terminology, test methods and general performance requirements | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 8536-13:2025 Infusion equipment for medical use — Part 13: Graduated flow regulators for single use with fluid contact | 40.20 | BAS/TC 25 | 13.10.2025 | 12.12.2025 |
| nsBAS ISO 8549-4:2025 Prosthetics and orthotics — Vocabulary — Part 4: Terms relating to limb amputation | 40.20 | BAS/TC 25 | 13.10.2025 | 12.12.2025 |
| nsBAS ISO 8653:2025 Jewellery — Ring-sizes — Definition, measurement and designation | 40.20 | BAS/TC 38 | 31.10.2025 | 30.11.2025 |
| nsBAS ISO 8714:2025 Electric road vehicles — Reference energy consumption and range — Test procedures for passenger cars and light commercial vehicles | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 8820-11:2025 Road vehicles — Fuse-links — Part 11: Fuse-links with tabs (blade type) Type M (medium-high current) | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 8820-12:2025 Road vehicles — Fuse-links — Part 12: Fuse-links with tabs (blade type) Type N (sub miniature) | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO 8820-13:2025 Road vehicles — Fuse-links — Part 13: Fuse-links with tabs (blade type) Type P (sub miniature three tabs) | 40.20 | BAS/TC 35 | 29.10.2025 | 28.12.2025 |
| nsBAS ISO/IEC 10373-1/A1:2025 Cards and security devices for personal identification — Test methods — Part 1: General characteristics — Amendment 1: Clarification of peel strength test method to be used for ISO/IEC 7810 conformance testing | 40.20 | BAS/TC 1 | 03.10.2025 | 03.11.2025 |
| nsBAS ISO/IEC 14443-2/Cor2:2025 Cards and security devices for personal identification — Contactless proximity objects — Part 2: Radio frequency power and signal interface — Technical Corrigendum 2 | 40.20 | BAS/TC 1 | 03.10.2025 | 03.11.2025 |
| nsBAS ISO/IEC 24787-1:2025 Information technology — On-card biometric comparison — Part 1: General principles and specifications | 40.20 | BAS/TC 1 | 03.10.2025 | 03.11.2025 |